What is the firing order for 2006 Chevy Impala LT 3.5L - Cars & Trucks (2024)

SOURCE: 2007 Chevy Impala LT stock stereo

pop out the center trim piece with a flat head screwdriver. Center dash piece may be brushed aluminum or wood grain depending on trim level. It should pop out easily working all the way around it. Then radio is held in with 7mm screws.

SOURCE: How do I program my key for my 2006 Chevy Impala?

Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

SOURCE: 2006 Chevy Impala reduced engine power

best bet is to stop in at a Pep Boys, Autozone, or similar big autoparts seller, and ask for free trouble code scan, which should pinpoint area causing problem. If not obvious by codes, what is necessary to repair the problem code, get back to us with those codes and we will be glad to assist you further. Better this way, takes away the guess work, and saves you money, as well as getting it right the first time.

SOURCE: WHAT IS THE FIRING ORDER FOR A CHEVY IMPALA 3.4L

1 2 3 4 5 6 (no joke) the side nearest the radiator is 4-6 and the back is 1-3. the numbers should be on the coils but let me know if they are not.

SOURCE: firing order for plugs and wires....on a v6 3800 2000 impala

For the 2000 Chevrolet Impala 3.8L V6:

Firing Order:
1-6-5-4-3-2

Cylinders:

Ignition Coil Connections:

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Upload

Upload an image from your computer

Loading...

prevnext

0helpful

1answer

0helpful

2answers

0helpful

1answer

0helpful

1answer

0helpful

1answer

0answers

0helpful

1answer

That is an actuator in the heat and cooling system

3helpful

1answer

For the 2001 Chevrolet Impala
I do not know if you have the 3.4L or 3.8L however I have included both below:

For the 3.4L V6:
Firing Order:
1-2-3-4-5-6
Ignition Connections:
............(back)...........
.'.5..2.'..'.3..6.'..'.4..1.'
............(front)

For the 3.8L V6:
Firing Order:
1-6-5-4-3-2
Cylinders:
.....(back).....
'...2...4...6...'
___________
'...1...3...5...'
.....(front)

Ignition Coil Connections:

4helpful

2answers

6helpful

1answer